• Diseño de la placa de pared – Se adapta convenientemente a una caja trasera de dos bandas de los Estados Unidos para una fácil instalación en una pared, piso o atril. Utiliza planchas de estilo estándar de decoración (no incluidas). Está disponible en negro o blanco y tiene un diseño industrial que se mezcla bien en instalaciones comerciales.
• Baja Latencia – Con 1 frame de latencia para codificar más decodificar (34 ms para 4K30 y 17 ms para 1080p60), la Serie N2300 ofrece distribución de video con latencia casi imperceptible.
• Compatibilidad con HDMI 2.0 y HDCP 2.2 – Al incorporar HDMI 2.0 y HDCP 2.2, los productos de la serie N2300 son compatibles con las últimas fuentes y pantallas 4K.
• PoE Powered – Sólo requiere un cable de categoría para el transporte de alimentación y audio/vídeo, lo que simplifica en gran medida los requisitos de instalación.
• Nativo NetLinx – Simplifica la integración con el control AMX para reducir el coste de instalación.
• Flexibilidad de diseño – Empiece desde un 1×1 y haga crecer el sistema simplemente añadiendo codificadores y decodificadores adicionales.

VIDEO

• Digital Video Input: HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*
• Analog Video Input: HD-15 VGA, Component*
• Video Output: Video Output
• Formats: HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*, HDCP content protection support, RGBHV, YPbPr
• Progressive Input Resolutions
  • Supports most common HD up to 1920×1200.
  • See NMX-ENC-N2315 Installation Manual for all supported resolutions
  • HDMI and DVI (Progressive)
    • Pixel clock between 27 MHz – 300MHz
    • Minimum resolution of 720x480p60
    • Maximum horizontal resolution of 4096 or a vertical resolution of 2160*
    • Common acceptable resolutions include: 720x480p60 – 480p, 720×576@50, 800x600p60, 1024x768p60, 1280×720@60Hz – 720p60, 1600×1200@60Hz, 1920×1080@60Hz – 1080p60, 3840×2160(4:2:0)@30Hz – UHD30 aka 4K30, 4096×2160(4:2:0)@30Hz – DCI 4K30
• Interlaced Input Resolutions
  • Supports 1080i60.
  • See NMX-ENC-N2315 Installation Manual for all supported resolutions
  • HDMI and DVI (Interlaced): 1920×1080@50Hz – 1080i50, 1920×1080@60Hz – 1080i60
  • Note: Interlaced resolutions will be de-interlaced if scaled on the decoder; otherwise, the interlaced signal will pass through to the displayAnalog Input Resolutions
  • NOTE: Input resolutions supported @60Hz refresh rates are also supported @59.94Hz.
• Analog Input Resolutions
  • Supports most common HD resolutions up to 1920×1200
  • See NMX-ENC-N2315 Installation Manual for all supported resolutions
  • VGA
    • Pixel clock between 27 MHz – 165 MHz
    • Minimum resolution of 640×480
    • Maximum horizontal resolution of 1920 or a vertical resolution of 1200
    • Common acceptable resolutions include: 640x480p60, 720x480p60 – 480p, 720×576@50, 800x600p60, 1024×768@60Hz, 1280×720@50Hz (720p50), 1280×720@60Hz (720p60), 1280×768@60Hz, 1280×800@60Hz, 1280×960@60Hz, 1280×1024@60Hz, 1360×768@60Hz, 1366×768@60Hz, 1400×1050@60Hz, 1440×900@60Hz, 1600×1200@60Hz, 1680×1050@60Hz, 1920×1080@50Hz (1080p50), 1920×1080@60Hz (1080p60), 1920×1200@60Hz (reduced blanking)
  • Note: Input resolutions supported @60Hz refresh rates are also supported @59.94Hz
  • The N2315 Encoder does not accept Composite or S-Video (YC)
• Analog-To-Digital Conversion: 8-bit 165 MHz per each of three color channels
• Color Space: 4:2:0 4K30, 4:2:2 – HD
• LocalPlay/HostPlay: 8 playlists
• HostPlay: 1 image/list
• Note: Jumbo Frames Required
• Video Wall Construction: Supported within the NMX-DEC-N2322, the N2300 Series is not compatible with SVSI Windowing Processors at this time
• Network Video Recording: Not compatible with SVSI NVR at this time

AUDIO

• Input Signal Types: Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo
• Output Signal Types: Ethernet
• Analog Audio Format: 8ch PCM, Stereo 2-channel
• Analog-To-Digital Conversion: 16-bit 32 kHz, 44.1 kHz and 48 kHz
• Input Signal Types: Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo

LATENCY

• 17-ms at 60 fps for 1920×1080 and lower resolutions
• 34-ms at 30 fps for 4K30
• NOTE: This is the combined encode plus decode latency. Total latency from source to screen will also include any network latency.
• Scaling adds one frame of latency (17ms at 60fps)

BANDWIDTH

• 200 Mb/s (average)
• Note: Bandwidths can be as high as 700 Mb/s, depending on the resolution and the amount of motion in the video content.
• Note: Minimum bandwidth is 50 Mb/s for resolutions <= 1080p60Bandwidth: 840 Mb/s (varies with resolution)

COMMUNICATIONS

• Ethernet-PO: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
• Ethernet-PI: 1 Gbps port which accepts compatible fiber transceivers or direct attach cables, DHCP, Auto IP, and static IP
• HDMI: HDCP, EDID management

PORTS

• P0:
  • 8-wire RJ45 female
  • 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
  • Provides the network connection, network AV video, and power to the Encoders and Decoders
• HDMI IN: HDMI video input
• VGA IN: DB15 analog input
• USB IN – Host: USB-B host input
• USB IN – Maintenance: USB-Mini maintenance input

CONTROLS AND INDICATORS – FRONT PANEL

• RESET Button:
  • Recessed pushbutton
  • Press to initiate a ‘warm restart’ causing the processor to reset, but not lose power. A reset does NOT affect the current settings
• POWER LED: On solid (green) when operating power is supplied (via PoE or local power supply)
• AUDIO LED: On (green) when audio is transmitting.
• ANALOG VIDEO LEDs: On (green) when analog source is available and transmitting.

POWER SUPPLY

• Power over Ethernet
  • Can be powered via a PoE switch or other equipment with a PoE source. Conforms to IEEE 802.3af Class 3 (802.3at Type 1)
  • Point-to-point applications between the encoder and a decoder requires a PoE injector to power the wallplate encoder.

Note: In order for the unit to receive Power over Ethernet (PoE), it must be connected to a switch or other equipment that has a PoE PSE (Power Sourcing Equipment) port. Warning: Do not run wiring that is connected to a PoE PSE port outside of the building where the PSE resides. It is for intra-building use only.

ENVIRONMENTAL

• Temperature (Operating): 32° to 104°F (0° to 40°C)
• Temperature (Storage): -22° to 158°F (-30° to 70°C)
• Humidity (Operating): 10% to 90% RH (non-condensing)
• Humidity (Storage): 0% to 90% RH (non-condensing)
• Heat Dissipation: Up to ~26 BTU/hr

GENERAL

• Dimensions (HWD): 4.06″ x 3.5″ x 2.25″ (10.31 cm x 8.84 cm x 5.72 cm)
• Weight: .75 lb (0.34 kg)
• Airflow: Natural convection via vent openings on front, back, and top
• Installation
  • Mounts onto standard 2 gang US back boxes
  • Mounts into standard décor style wallplates (not included)
• Regulatory Compliance: FCC, CE, and NTRL
• Recommended Accessories
  • Compatible with N2300 Series Encoders and Decoder
  • PS-POE-AT-TC High-Power PoE Injector, 802.3AT Compliant FG423-84)

Nota importante: Las especificaciones pueden sufrir cambios.

El NMX-ENC-N2315 es la solución perfecta para cualquier aplicación que requiera una matriz de vídeo más pequeña que 32×32. Las aplicaciones más comunes incluyen salas de conferencias, espacios de reuniones y atriles (dentro o adyacentes).

Llame al 954 189 006